I recently signed up for a Simon Says Card Kit of the Month and because I live in Canada, It did not get here until a few days ago (September 20th!). I was so excited to get this month’s kit for a few reasons. First of all, it had two stamp sets in it. and secondly, one of the stamps was a large stamp, my first ever.
Heads Up, before we go any further, this is a SHORT post!
My first look at the stamp and I was so excited. I knew what I wanted to do: use clear embossing ink and heat emboss. I lined it up in my stamping tool and dabbed embossing ink on it. STAMP. Not all areas of the stamp got inked!
Try number two, inked it all up. STAMP. Spaces in the image. Glad to have my stamping tool! I was ok to keep going as the image was stamping in the same spot over and over because of the stamping tool: mine is a Tim Holtz tool.
Well, I have to say by the fourth try, I was fed up! I decided that since I put all this energy into the thing, I might as will heat emboss what I could. I finished up the heat embossing and wondered if I could cut the image apart and used the pieces in different cards… I figured, hey, I have spent a good 15 mn with this, let me colour it in and see what it looks like before I start the cutting process..
So I coloured in the image MY STYLE which translates to no real knowledge of shading etc. Once it was finished I fussy cut it out.
I have to say that given all the mistakes with me not stamping it correctly, and colouring it incorrectly, I still like how it looks.
Next time I will not cut it out as there is too much inner white space, so I will just stamp it on the card base that I will use.
I was looking for an interactive card to make as I LOVE paper creations that move when I came across a few people making a gumball machine that dispenses candy. YEP, it really worked. So I wanted to make my own card and tried out one of the videos with so-so success. After looking at a few different ways to put this card together, I decided to do my own, so below is what I did and some tips on what worked. I will give instructions for both solid cardstock and the cardstock/foam tape version.
Give some credit!
So before I begin with my own design, I would like to list the places I saw this card.
Here is a list of what you will need to make this card
Heavy cardstock 110 pound
Decorative Cardstock for gumball machine.
Double sided foam tape
Double sided sticky tape
Acetate for shaker window
Candy: mini M&M or Tic Tac
Optional chipboard 1/8 inch thick
My SVF file or your Circle Dies- 2 in, 1 in, 1/2 inch
Easier Than You Think
Ok, I am going to give quite a bit of detail below and although I hope to be clear in the instruction, you may look at it and think it’s complicated. It’s NOT! The general assembly once everything is cut takes about 15 minutes.
The piece we will use are named for easy reference
Gumball Card Base
Guide Mechinism which looks like a rectange and a odd lightbulb shape cut out
Dispensing Mechinism looks like a circle with a wedge shape cut out – PacMan shaped for those of you old enough to remember!
Handle made up of small circles and rectangles
Optional 1/4 inch strips to cut for a tidy finish.
Lid to cover the refilling candy space.
Gumball Machine Body
Greeting Card base
Gumball Card Base – Cut 1
CUT 1 of the Gumball Card Base
Cut a piece of acetate 4 inches long by 3 inches wide and using double-sided tape/glue, cover the larger (shaker) window.
Glue the acetate to the back of the Gumball Card Base – choose any side to be the back. Glue or double-sided tape can be used and will not show when the card is finished.
Additional information: The size for the Gumball Card Base was taken from the Tiffany Yu version. The size of the Gumball Card Base used in this file is 4 inches by 5.25 inches. I found this Gumball Card Base size to be perfect. I did try using 65-pound cardstock in my trial version but decided on the heavier 110-pound cardstock. All of the various parts are made using 110-pound cardstock with an option to use less cardstock by using a combination of Cardstock, foam tape, and use 1/8 inch chipboard for the inner part of this card. You will need a Cricut Maker to cut the chipboard if you decide to use this material. The size of the circles on this card base is 2 inches, 0.55 inches and 1 inch cut partially for the tray. When I made the file, The position of the window (2 inches) and The mechanism/handle turned out to be crucial in a smooth dispensing of candy.
The inner part of this interactive card has two parts, First is the Guide Mechanism for the candy to move from the window to the Dispensing Mechanism that catches the candy and dispenses it.
Cut 1, 8, or 12 of these depending on what you decide after reading the additional material below.
Foam tape can be used in between the cutout pieces in any fashion you like to bring the inner mechanism to the required 1/4 inch.
Glue the assembled Guide Mechanism to the back of the Gumball Card Base
Option 1: Use 12 pieces of Inner Mechanism cut from 110-pound cardstock. My image below the inner mechanism is not yet glued together. This version does not need anything extra to protect against a sticky edge.
Additional information: We need to create a space between the shaker window and the back of the card that will allow the candy to flow smoothly. If the candy is flat, the mini M&M is about 1/4 inch. If it ends up sideways then it needs 1/2 inch.
I used 1/4 inch spacing, and if any went sideways, a little shake fixed the issue. To get this space, I stacked and glued 8 of the inner mechanism and then used 2 layers of foam tape.
You can also get a 1/4 inch space by using all foam tape: Cut one of the inner mechanisms to use as a guide and then put foam tape on all of the solid areas. Don’t go too close to the cutout section in the middle of the Guide Mechanism as you don’t want the candy sticking to the foam. If you decide to use only foam tape, you will have to use a 1/4 strip of paper to cover the sticky edge later on in the assembly or dust the sticky edge with powder to get rid of the stickiness. A 1/4 inch strip to cut is included in the file.
You can also use only cardstock, cut 12 pieces, and glue them together. This will make your card a little heavy, so if you are thinking of mailing it your postage may increase
Option 2: Use 1 piece of Inner Mechanism cut from 110-pound cardstock. Use foam tape to build the space to be 1/4 inch. We will need to use a 1/4 inch strip of paper to cover the inner edge of the inner mechanism so that the candy does not get stuck. with any foam tape use, this strip of paper to cover the sticky edge is needed.
Cut 1,8 or 12 of the Dispensing Mechanism after reading additional information below
Cardstock foam tape: use 1 Dispensing Mechanism cut from cardstock and layer foam to create a 1/4 high object. This is best done as described by Tiffany Yu. Cut 4 1 inch circles and cut in half. Layer on the bottom of Dispensing Mechanism. Cut 2 half circles 1 inch in diameter and fold each piece in half. Layer on the solid wedge area.
Cardstock only: For the Dispensing Mechanism, you can also use only cardstock: cut 10 to 12 of the Dispensing Mechanisms and glue them together to form a 1/4 inch thick object. Cover each side with a solid 1-inch circle.
Insert the assembled Dispensing Mechanism to the back of the Gumball Card Base so that it looks like this below. note that yours will have the additional solid circle covering this Dispensing Mechanism so the wedge will not actually be visible.
Final Assembly of The Card
Cut 1 of each
The Gumball machine consists of a gumball base and a circle. These are glued to the front of the card Base
Cut 8 of the .5 inch circles and 8 of the 1-inch rectangles cut and 1 out of decorative paper
The handle has 2 parts: first is the 8 small circles about .5 inches in diameter that are glued and stacked and then finished off with the rectangular part of the handle made up of 8 pieces of cardstock. Put this through the .55 inch hole in the front and glue it to the Dispensing Mechanism that is at the back
The removeable stopper to refill the gumballis simply two pieces of cardstock with foam tape and some string snadwitched between them. The finished thickness should be 1/4 inch.
Greeting Card Base
Greeting Card Base 8.5 by 5.5 folded in half. The entire assembled Dispensing Gumball Machine is adhered to the front of this card. You can stamp a message in the shaker window area so that when the candy is finished, there is a message.
Well, All Done
Once you attach the finished gumball machine, adhear to the front of your greeting card and fill with candy. The stopper prevents the candy from falling out and can be removed to refill.
If you would like the svg file, drop me a note and I will email it to you. The file below is PDF.